![]() Important: Make sure the fabric you use allows for water to drain from the bottom of the planter. Staple it in place so you can fill the planter with soil without worrying that the fabric may shift under it. Line the inside of the box with landscape fabric. ![]() Last but not least, prepare the box for the soil. Tip: Stain all of it, including the inside and the back, to make sure it won’t rot. Staining your new privacy screen planter will make it ready for outside weather. You’re almost there, make sure you don’t skip this step. Cut them at a 45-degree angle so that they fit together well. If you use a pallet board or nail boards across the posts, finials may not be necessary.Īlso optional is to add four horizontal boards to the top of the box. Glue the finials to the top of the 4x4s for a more finished look. Or you can use long boards that reach from one 4×4 post to the other. Tip: If you use wood boards to build a custom screen, you can reinforce the boards with a longer vertical board that runs behind the screen. You may have to use a jigsaw to cut the lattice or pallet to the right size to fit the boards. Simply nail the privacy screen to the 4×4 posts. Whether you choose to use a wooden lattice, pallet, or wood boards, the process is the same. Depending on the width you want for the planter, you could make two or three side boards from one long 1×6 cedar board. Work the front and back first and then the sides. Fix each board with two or more screws at both ends. Start from the top so that the first board is flush with the top of the frame. Now it’s time to make your privacy screen planter look nice.Īdd the 1×6 cedar boards to the frame you’ve made. Get someone to help you handle the frame. So that the frame doesn’t sit directly on the ground, you can add 4 feet to the frame. Note: Depending on the size of the planter, you may have to use more than 10 floorboards. ![]() Work this part with the frame and screen posts standing up. Step 5 – Add the floorboardsĪdd the floorboards, screwing each in place with two 2 ½ inch screws at both ends. For this, you’ll have to drive some more screws through the 4x4s so that they reach the ends of the “C” sides. Next, you want to attach the back side of the frame to the front. Tip: It’s easier to do this with the 4x4s lying on the ground. Drive two or more screws where the wood meets.įix the 4x4s with screws to the ends of the other horizontal “H” to create the back of the frame. Step 4 – Attach the frame to the privacy screen supportsĪttach the two “C” sides to one of the longer, upturned “H” sides to create the front of the frame. This part of the frame should look like a big “C”. Now it’s time to build the sides of the frame.Īttach two short 2×6 pieces to a side piece using one diagonal pilot hole and screw for each. Don’t worry about the ends of the frame just yet. Repeat the process for the other part of the frame. You should end up with a large, horizontal “H”. For this, drive holes through the other end of the shorter piece and into the long board. Turn it over and attach the other long 2×6 board to it. Drive screws through the diagonal holes and fix the short piece in place. Place one of the shorter pieces of 2×6 board vertically at the centre of a long 2×6 board. ![]() Step 2 – Assemble the long sides of the frame Based on this, you may also have to cut the two 4x4s that will support it. Important: Determine the height of the privacy screen. You’ll also need two 2×6 shorter pieces for extra support at the centre of the longer sides. For a sturdy frame, you’ll need four 2×6 long pieces and six 2×6 shorter pieces for the sides. Cut the lumber for the frame to the desired length. You can make the privacy screen as big as you need it to be.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |